Linux version 2.6.18-308.1.1.el5PAE (mockbuild@builder10.centos.org) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-52)) #1 SMP Wed Mar 7 04:57:46 EST 2012 BIOS-provided physical RAM map: BIOS-e820: 0000000000010000 - 00000000000a0000 (usable) BIOS-e820: 0000000000100000 - 00000000dffc0000 (usable) BIOS-e820: 00000000dffc0000 - 00000000dffcfc00 (ACPI data) BIOS-e820: 00000000dffcfc00 - 00000000dffff000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved) BIOS-e820: 00000000fed13000 - 00000000feda0000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000120000000 (usable) 3712MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000fe710 Memory for crash kernel (0x0 to 0x0) notwithin permissible range disabling kdump NX (Execute Disable) protection: active On node 0 totalpages: 1179648 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 950272 pages, LIFO batch:31 DMI 2.4 present. DMI: Dell Computer Corporation PowerEdge 860/0XM089, BIOS A04 07/24/2007 Using APIC driver default ACPI: RSDP (v002 DELL ) @ 0x000fa030 ACPI: XSDT (v001 DELL PE_SC3 0x00000001 MSFT 0x0100000a) @ 0x000fa0a0 ACPI: FADT (v003 DELL PE_SC3 0x00000001 MSFT 0x0100000a) @ 0x000fa188 ACPI: MADT (v001 DELL PE_SC3 0x00000001 MSFT 0x0100000a) @ 0x000fa27c ACPI: SPCR (v001 DELL PE_SC3 0x00000001 MSFT 0x0100000a) @ 0x000fa300 ACPI: HPET (v001 DELL PE_SC3 0x00000001 MSFT 0x0100000a) @ 0x000fa350 ACPI: MCFG (v001 DELL PE_SC3 0x00000001 MSFT 0x0100000a) @ 0x000fa388 ACPI: DSDT (v001 DELL PE_SC3 0x00000001 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0xffffffff base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at e0000000 (gap: dffff000:10001000) Detected 2133.458 MHz processor. Built 1 zonelists. Total pages: 1179648 Kernel command line: ro root=/dev/VolGroup00/LogVol00 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c0771000 soft=c0751000 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 4146888k/4718592k available (2204k kernel code, 45844k reserved, 914k data, 232k init, 3276544k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Using HPET for base-timer Calibrating delay loop (skipped), value calculated using timer frequency.. 4266.91 BogoMIPS (lpj=2133458) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 monitor/mwait feature present. using mwait in idle threads. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e3bd 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20060707 CPU0: Intel(R) Xeon(R) CPU 3050 @ 2.13GHz stepping 02 SMP alternatives: switching to SMP code Booting processor 1/1 eip 11000 CPU 1 irqstacks, hard=c0772000 soft=c0752000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4266.82 BogoMIPS (lpj=2133411) CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e3bd 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel(R) Xeon(R) CPU 3050 @ 2.13GHz stepping 02 Total of 2 processors activated (8533.73 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 Using local APIC timer interrupts. checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs sizeof(vma)=88 bytes sizeof(page)=32 bytes sizeof(inode)=340 bytes sizeof(dentry)=136 bytes sizeof(ext3inode)=492 bytes sizeof(buffer_head)=52 bytes sizeof(skbuff)=176 bytes migration_cost=24 checking if image is initramfs... it is Freeing initrd memory: 3470k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 0880-08bf claimed by ICH6 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: PXH quirk detected, disabling MSI for SHPC device PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PES1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEP0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEP1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEP2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIS._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 *6 7 9 10 11 12) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default pnp: 00:08: ioport range 0x800-0x87f could not be reserved pnp: 00:08: ioport range 0x880-0x8bf has been reserved pnp: 00:08: ioport range 0x8c0-0x8df has been reserved pnp: 00:08: ioport range 0x8e0-0x8e3 has been reserved pnp: 00:08: ioport range 0xc00-0xc0f has been reserved pnp: 00:08: ioport range 0xc10-0xc1f has been reserved pnp: 00:08: ioport range 0xca0-0xca7 has been reserved pnp: 00:08: ioport range 0xca9-0xcab has been reserved pnp: 00:0a: iomem range 0xf0000000-0xf3ffffff has been reserved PCI: Bridge: 0000:01:00.0 IO window: e000-0000 MEM window: fe900000-00000000 PREFETCH window: disabled. PCI: Bridge: 0000:00:01.0 IO window: e000-0000 MEM window: fe700000-00000000 PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: d000-0000 MEM window: fe500000-00000000 PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.5 IO window: c000-0000 MEM window: fe300000-00000000 PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: b000-0000 MEM window: fe100000-00000000 PREFETCH window 0x00000000e8000000-0x00000000efffffff ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Setting latency timer of device 0000:01:00.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 21 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.4[B] -> GSI 22 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1c.4 to 64 ACPI: PCI Interrupt 0000:00:1c.5[C] -> GSI 23 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:1c.5 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered apm: BIOS not found. audit: initializing netlink socket (disabled) type=2000 audit(1516568985.712:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API alg: No test for crc32c (crc32c-generic) ksign: Installing public key data Loading keyring - Added public key FFABC2B2452CFF5B - User ID: CentOS (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:06:05.0 PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Setting latency timer of device 0000:00:1c.0 to 64 PCI: Setting latency timer of device 0000:00:1c.4 to 64 PCI: Setting latency timer of device 0000:00:1c.5 to 64 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A brd: module loaded Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH7: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0000 -> 0001) ACPI: Unable to derive IRQ for device 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[A]: no GSI ICH7: chipset revision 1 ICH7: not 100% native mode: will probe irqs later ICH7: neither IDE port enabled (BIOS) Probing IDE interface ide0... Probing IDE interface ide1... ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode ACPI: (supports S0 S4 S5) Initalizing network drop monitor service Freeing unused kernel memory: 232k freed Time: tsc clocksource has been installed. Write protecting the kernel read-only data: 416k input: AT Translated Set 2 keyboard as /class/input/input0 ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 50 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 50, io mem 0xfeb00000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 50 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 50, io base 0x0000ace0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 177, io base 0x0000acc0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-3: new high speed USB device using ehci_hcd and address 2 ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 185, io base 0x0000aca0 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb 1-3: configuration #1 chosen from 1 choice hub 1-3:1.0: USB hub found hub 1-3:1.0: 4 ports detected SCSI subsystem initialized Fusion MPT base driver 3.04.20rh Copyright (c) 1999-2008 LSI Corporation Fusion MPT SAS Host driver 3.04.20rh ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 16 (level, low) -> IRQ 169 mptbase: ioc0: Initiating bringup ioc0: LSISAS1068 B0: Capabilities={Initiator} scsi0 : ioc0: LSISAS1068 B0, FwRev=000a3100h, Ports=1, MaxQ=286, IRQ=169 mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 32, phy 0, sas_addr 0x1221000000000000 Vendor: ATA Model: ST3160812AS Rev: J Type: Direct-Access ANSI SCSI revision: 05 mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 1, phy 1, sas_addr 0x1221000001000000 Vendor: ATA Model: ST3160812AS Rev: J Type: Direct-Access ANSI SCSI revision: 05 mptsas: ioc0: attaching raid volume, channel 1, id 0 Vendor: Dell Model: VIRTUAL DISK Rev: 1028 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 310546432 512-byte hdwr sectors (159000 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write through SCSI device sda: 310546432 512-byte hdwr sectors (159000 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write through sda: sda1 sda2 sd 0:1:0:0: Attached scsi disk sda libata version 3.00 loaded. Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.11.6-ioctl (2011-02-18) initialised: dm-devel@redhat.com device-mapper: dm-raid45: initialized v0.2594l kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. type=1404 audit(1516569017.895:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 security: 3 users, 6 roles, 2067 types, 278 bools, 1 sens, 1024 cats security: 61 classes, 83426 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev dm-0, type ext3), uses xattr SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts type=1403 audit(1516569018.202:3): policy loaded auid=4294967295 ses=4294967295 input: PC Speaker as /class/input/input1 intel_rng: FWH not detected EDAC MC: Ver: 2.0.1 Mar 7 2012 ACPI: Unable to derive IRQ for device 0000:00:1f.3 ACPI: PCI Interrupt 0000:00:1f.3[B]: no GSI Floppy drive(s): fd0 is 1.44M tg3.c:v3.119 (May 18, 2011)<6>ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:04:00.0 to 64 tg3 0000:04:00.0: eth0: eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:1c:23:e1:5c:91 tg3 0000:04:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] tg3 0000:04:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 17 (level, low) -> IRQ 58 PCI: Setting latency timer of device 0000:05:00.0 to 64 tg3 0000:05:00.0: eth1: eth1: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:1c:23:e1:5c:92 tg3 0000:05:00.0: eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] tg3 0000:05:00.0: eth1: dma_rwctrl[76180000] dma_mask[64-bit] EDAC MC0: Giving out device to i3000_edac i3000: DEV 0000:00:00.0 scsi 0:0:0:0: Attached scsi generic sg0 type 0 scsi 0:0:1:0: Attached scsi generic sg1 type 0 sd 0:1:0:0: Attached scsi generic sg2 type 0 floppy0: no floppy controllers found work still pending Floppy drive(s): fd0 is 1.44M floppy0: no floppy controllers found work still pending lp: driver loaded but no devices found ACPI: Power Button (FF) [PWRF] ACPI: Mapper loaded dell-wmi: No known WMI GUID found md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. device-mapper: multipath: version 1.0.6 loaded EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda1, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs Adding 5668856k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:5668856k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts IA-32 Microcode Update Driver: v1.14a microcode: CPU1 updated from revision 0x56 to 0x5d, date = 10022010 microcode: CPU0 updated from revision 0x56 to 0x5d, date = 10022010 Loading iSCSI transport class v2.0-871. 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller libcxgbi:libcxgbi_init_module: tag itt 0x1fff, 13 bits, age 0xf, 4 bits. libcxgbi:ddp_setup_host_page_size: system PAGE 4096, ddp idx 0. Chelsio T3 iSCSI Driver cxgb3i v2.0.0 (Jun. 2010) iscsi: registered transport (cxgb3i) NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011) Broadcom NetXtreme II iSCSI Driver bnx2i v2.7.0.3 (Aug 04, 2011) iscsi: registered transport (bnx2i) iscsi: registered transport (tcp) iscsi: registered transport (iser) iscsi: registered transport (be2iscsi) ip6_tables: (C) 2000-2006 Netfilter Core Team ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 228 bytes per conntrack ADDRCONF(NETDEV_UP): eth0: link is not ready SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 Bluetooth: HIDP (Human Interface Emulation) ver 1.1 SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts usb 1-3.2: new high speed USB device using ehci_hcd and address 3 usb 1-3.2: configuration #1 chosen from 1 choice scsi1 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning Vendor: Model: Rev: 8.07 Type: Direct-Access ANSI SCSI revision: 04 SCSI device sdb: 15503360 512-byte hdwr sectors (7938 MB) sdb: Write Protect is off sdb: Mode Sense: 23 00 00 00 sdb: assuming drive cache: write through SCSI device sdb: 15503360 512-byte hdwr sectors (7938 MB) sdb: Write Protect is off sdb: Mode Sense: 23 00 00 00 sdb: assuming drive cache: write through sdb: sdb1 sd 1:0:0:0: Attached scsi removable disk sdb sd 1:0:0:0: Attached scsi generic sg3 type 0 usb-storage: device scan complete SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts